Why My Canon Pixma MG2520 Paper Not Feeding?

HOME
PRINTERS
Paper Feeding Issue On Canon Pixma Printer

Paper Not Feeding Issue On Canon Pixma MG2520 Printer

Paper Not Feeding

Paper not feeding while printing is not a new issue. The error seems complicated, but at the same time, you can resolve it easily and quickly by performing simple troubleshooting steps. This page will assist you in resolving the Canon Pixma MG2520 paper not feeding issue

Initially, check whether your Canon printer’s rear tray contains paper. If not, load enoughpaper in the rear tray.

While loading the paper, make sure not to exceed the maximum limit of the tray.

Avoid loading curled or dirty paper in the rear tray because using these kinds of paper will lead to the paper notbeing

Make sure that you’re only loading the paper that is recommended by the Canon.

Check if there is any paper or foreign object jammed insidethe rear tray. If yes, remove it carefully without damaging it further. To remove the foreign object from the rear tray, turn off your printer and disconnect its power cable from the wall outlet, and then remove the foreign object.

If these basic solutions couldn’t resolve the Canon MG2520 paper not feeding issue, then perform the advanced method discussed below.

Advanced method

Solution 1: Clean the Paper Feed Roller

If your Canon printer’s paper feed roller contains dust or dirt particles, then there is a chance for this issue to occur. To clean the paper feed roller, carry out the below instructions.

You can clean the roller in two different ways.

Using paper
Without using paper

Method 1: Using Paper

Load a clean plain paper in the rear tray of your printer. Make sure to load this paper only after the roller stops rolling.
Similarly, make sure that your printer’s output tray and the output tray extension are pulled out.
Now, press and hold your printer’s Stop
Once the orange light flashes seven times, release the button.
Now, your Canon printer will automatically clean the paper feed roller.

Method 2: Without using paper

Remove the paper from the rear tray if present.
Hold down theStop button on the printer.
Make sure to release the button only after the orange light flashes seven times.
Now, the roller cleaning will be initiated successfully.

Now, check if the issue is resolved. If not, manually clean your printer’s paper feed roller.

Solution 2: Manually cleaning the paper feed roller

Make sure that your printer is turned off and its power cable is disconnected from the wall outlet.
Get a clean, moist cotton swab and clean your printer’s paper feed roller.
Make sure not to touch the roller using your figures.
After cleaning the roller, wait for sometimes it to dry.
Reconnect the power cable to the printer and turn it on.

If the Canon Pixma MG2520 paper not feeding issue persists even after manually cleaning the paper feed roller, then contact us for more assistance.

Why is my wireless printer not printing?

First, try restarting your computer, printer and wireless router. To check if your printer is connected to your network: Print a Wireless Network Test report from the printer control panel. On many printers pressing the Wireless button allows direct access to printing this report.
Why is my printer showing error?

The other most probable reason for the printing error is the connection between your computer and the printer. If you are sure that the transmission cable is working okay (tested the printer on another computer), then the problem might be the drivers. This can be the printer drivers or the USB port drivers.
Why do my 3d prints keep failing?

Another common fail is over extrusion. Over extrusion happens when your 3D printer pushes out too much plastic too fast, causing a jam in the end of the nozzle. ... Make sure YOURu layer height is less than your nozzle diameter. Increase your cooling fan's power (this will cool the plastic and cause it to slow down)
What is the WPS button?

WPS stands for Wi-Fi Protected Setup. It is a wireless network security standard that tries to make connections between a router and wireless devices faster and easier. WPS works only for wireless networks that use a password that is encrypted with the WPA Personal or WPA2 Personal security protocols.
How do I reset my printer?

To restore your HP printer to factory-default settings, follow these steps. Turn the product off. Disconnect the power cable from the product for 30 seconds and then reconnect. Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button.

call